Hi,
On Mon, Feb 19, 2024 at 04:24:04PM +0800, Kin Seng wrote:
> My current nginx setup always kill the TCP connection after 5 minutes of
> inactivity, i.e no transaction.
> [From wireshark, nginx send RST to upstream server and then send FIN,ACK to
> downstream client]
This could be the normal behavior if you had 'proxy_timeout 5m;' in your config.
But since apparently you have 86400s as proxy timeout value, something else is
going on.
Could you provide more details like debug log for example?
> I have this setup which requires TLS1.2 connection connecting from my
> internal network [client application] to public network [server]. It only
> use TCP ports (not http/https) and establish with a server located at
> public network. The client application does not support TLS1.2 connection
> hence the introduction of nginx proxy/reverse proxy for TLS wrapping
> purpose. You may refer below :
>
> Internal Network
> | INTERNET/Public
> [Client Application] <-----> [NGINX Reverse Proxy] <--- | ---> [Public
> Server]
> <Non TLS TCP Traffic> <TLS 1.2>
>
>
> - using stream module
> - no error shown in nginx error log
> - access log showing TCP 200 Status but the session only last 300s
> everytime. [Recorded in the access_log]
>
> Below is my nginx configuration
>
> # more nginx.conf
>
> user nginx;
> worker_processes auto;
> error_log /var/log/nginx/error.log;
> pid /run/nginx.pid;
>
> # Load dynamic modules. See /usr/share/doc/nginx/README.dynamic.
> include /usr/share/nginx/modules/*.conf;
>
> events {
> worker_connections 2048;
> }
>
> stream {
> resolver 127.0.0.1;
> include /etc/nginx/conf.d/*.conf;
>
> log_format basic '$remote_addr [$time_local] '
> '$protocol $status $bytes_sent $bytes_received '
> '$session_time $upstream_addr'
> '"$upstream_bytes_sent" "$upstream_bytes_received"
> "$upstream_connect_time"';
>
> access_log /var/log/nginx/stream.access.log basic;
>
> error_log log_file;
> error_log /var/log/nginx/error_log;
>
> server {
> listen 35012;
> proxy_pass X.X.X.X:35012;
> proxy_timeout 86400s;
> proxy_connect_timeout 1200s;
> proxy_socket_keepalive on;
> ssl_session_cache shared:SSL:5m;
> ssl_session_timeout 30m;
>
> # For securing TCP Traffic with upstream servers.
> proxy_ssl on;
> proxy_ssl_certificate /etc/ssl/certs/backend.crt;
> proxy_ssl_certificate_key /etc/ssl/certs/backend.key;
> proxy_ssl_protocols TLSv1.2;
> proxy_ssl_ciphers HIGH:!aNULL:!MD5;
>
> # proxy_ssl_trusted_certificate /etc/ssl/certs/trusted_ca_cert.crt;
> # proxy_ssl_verify on;
> proxy_ssl_verify_depth 2;
>
> #To have NGINX proxy previously negotiated connection parameters and use a
> so-called abbreviated handshake - Fast
> proxy_ssl_session_reuse on;
>
> }
> }
>
>
> After capturing the tcp packet and check via wireshark, I found out that
> the nginx is sending out the RST to the public server and then send FIN/ACK
> (refer attached pcap picture) to client application.
>
> I have tried to enable keepalive related parameters as per the nginx config
> above and also check on the OS's TCP tunable and i could not find any
> related settings which make NGINX to kill the TCP connection.
>
> Anyone encountering the same issues?
> _______________________________________________
> nginx mailing list
> nginx@nginx.org
> https://mailman.nginx.org/mailman/listinfo/nginx
--
Roman Arutyunyan
_______________________________________________
nginx mailing list
nginx@nginx.org
https://mailman.nginx.org/mailman/listinfo/nginx
