Welcome! Log In Create A New Profile

Advanced

Re: nginx for Windows - WSASend() socket error 10057

Yury Shpakov
February 14, 2020 06:10PM
So what is the meaning of Auth-Server and Auth-Port headers? So it's relevant only when nginx works as SMTP Proxy (not SMTP Server)? And these are host/port where to redirect SMTP requests?
Yeah, I was all the time surprised -- how come, it's set as Proxy but there is no setting where it redirects SMTP communication to. A little bit unexpected place for those setting.

Well, let me try...

I ran Fake SMTP Server on port 25.(I found on Internet some fake SMTP Server). I configured my test SMTP client to localhost:25 (later to 127.0.0.1:25). They send/receive successfully. So both SMTP Client and (fake) SMTP Server work fine.
127.0.0.1 works fine too.

I re-configured my test SMTP client to localhost:8025 (tried 127.0.0.1:8025 too). As well, I changed this section of config as follows:
http {
server {
listen 9000;

location /cgi-bin/nginxauth.cgi {
add_header Auth-Status OK;
add_header Auth-Server 127.0.0.1; # backend ip
add_header Auth-Port 25; # backend port
return 204;
}
}
}

The same error:
2020/02/14 17:37:18 [error] 15260#3328: *5 WSASend() failed (10057: A request to send or receive data was disallowed because the socket is not connected and (when sending on a datagram socket using a sendto call) no address was supplied) while in http auth state, client: 127.0.0.1, server: 0.0.0.0:8025

Update:
Detailed logging with debug information helped a lot.
This is what I noticed in there:

2020/02/14 17:40:28 [debug] 3940#22096: *1 smtp auth state
2020/02/14 17:40:28 [debug] 3940#22096: *1 WSARecv: fd:584 rc:0 24 of 4096
2020/02/14 17:40:28 [debug] 3940#22096: *1 smtp rcpt to:"RCPT TO:<ys@wmata.com>"
2020/02/14 17:40:28 [debug] 3940#22096: *1 event timer del: 584: 1172123084
2020/02/14 17:40:28 [debug] 3940#22096: *1 malloc: 02F8C260:2048
2020/02/14 17:40:28 [debug] 3940#22096: *1 stream socket 588
2020/02/14 17:40:28 [debug] 3940#22096: *1 connect to [::1]:9000, fd:588 #2
2020/02/14 17:40:28 [debug] 3940#22096: *1 select add event fd:588 ev:768
2020/02/14 17:40:28 [debug] 3940#22096: *1 select add event fd:588 ev:16
2020/02/14 17:40:28 [debug] 3940#22096: *1 event timer add: 588: 60000:1172123084
2020/02/14 17:40:28 [debug] 3940#22096: *1 event timer add: 588: 60000:1172123084

So it's trying to use IP6 rather than IP4.
And below:

2020/02/14 17:40:29 [debug] 3940#22096: *1 delete posted event 03171170
2020/02/14 17:40:29 [debug] 3940#22096: *1 mail auth http write handler
2020/02/14 17:40:29 [debug] 3940#22096: *1 WSASend: fd:588, -1, 0 of 306
2020/02/14 17:40:29 [error] 3940#22096: *1 WSASend() failed (10057: A request to send or receive data was disallowed because the socket is not connected and (when sending on a datagram socket using a sendto call) no address was supplied) while in http auth state, client: 127.0.0.1, server: 0.0.0.0:8025
2020/02/14 17:40:29 [debug] 3940#22096: *1 event timer del: 588: 1172123084
2020/02/14 17:40:29 [debug] 3940#22096: *1 event timer del: 588: 1172123084

So, I replaced localhost with 127.0.0.1 like this:
auth_http 127.0.0.1:9000/cgi-bin/nginxauth.cgi;

And it worked. Since I forced it to use IP4.
Any idea how to use host name instead of IP address and still have it working?

Update 2:
I figured it out. Googled a little bit and ended up with the following change to my config:

http {
server {
listen 9000;
listen [::]:9000 ipv6only=on;

location /cgi-bin/nginxauth.cgi {
add_header Auth-Status OK;
add_header Auth-Server 127.0.0.1; # backend ip
add_header Auth-Port 25; # backend port
return 204;
}
}
}

Now it works.
But why just "listen 9000" doesn't listen on both IP4 and IP6?
Is it a bug?


Yury
________________________________
From: Sergey Brester <serg.brester@sebres.de>
Sent: Friday, February 14, 2020 5:59 AM
To: Yury Shpakov <yshpakov@hotmail.com>
Cc: nginx-devel@nginx.org <nginx-devel@nginx.org>
Subject: Re: nginx for Windows - WSASend() socket error 10057


I don't know what is wrong with your config... I guess your smtp server does not answer properly.

Is 127.0.0.2:143 really your SMTP-server?
Because port 143 is mostly an IMAP port - but you've specified protocol smtp in the server section.

Anyway I tested your config with my settings (replaced name and smtp-server, here 192.0.2.222:25) and enabled debug:

+ error_log logs/error-mail.log debug;
mail {
- server_name localhost;
+ server_name example.com;
....
http {
....
- add_header Auth-Server 127.0.0.2;
- add_header Auth-Port 143;
+ add_header Auth-Server 192.0.2.222;
+ add_header Auth-Port 25;

it works well - I see the test incoming mail (I send to myself via 8025 port) and following output in the log (a lot of irrelevant messages are removed):

>>>>>>>>>

2020/02/14 11:24:04 [debug] 121280#128244: *1 smtp mail from:"mail FROM:<test@example.com>"
....
2020/02/14 11:24:04 [debug] 121280#128244: *3 http request line: "GET /cgi-bin/nginxauth.cgi HTTP/1.0"
2020/02/14 11:24:04 [debug] 121280#128244: *3 http uri: "/cgi-bin/nginxauth..cgi"
2020/02/14 11:24:04 [debug] 121280#128244: *3 http args: ""
2020/02/14 11:24:04 [debug] 121280#128244: *3 http exten: "cgi"
2020/02/14 11:24:04 [debug] 121280#128244: *3 http process request header line
2020/02/14 11:24:04 [debug] 121280#128244: *3 http header: "Host: localhost"
2020/02/14 11:24:04 [debug] 121280#128244: *3 http header: "Auth-Method: none"
2020/02/14 11:24:04 [debug] 121280#128244: *3 http header: "Auth-User: "
2020/02/14 11:24:04 [debug] 121280#128244: *3 http header: "Auth-Pass: "
2020/02/14 11:24:04 [debug] 121280#128244: *3 http header: "Auth-Protocol: smtp"
2020/02/14 11:24:04 [debug] 121280#128244: *3 http header: "Auth-Login-Attempt: 1"
2020/02/14 11:24:04 [debug] 121280#128244: *3 http header: "Client-IP: 127.0.0.1"
2020/02/14 11:24:04 [debug] 121280#128244: *3 http header: "Client-Host: [UNAVAILABLE]"
2020/02/14 11:24:04 [debug] 121280#128244: *3 http header: "Auth-SMTP-Helo: myhost.example.com"
2020/02/14 11:24:04 [debug] 121280#128244: *3 http header: "Auth-SMTP-From: mail FROM:<test@example.com>"
2020/02/14 11:24:04 [debug] 121280#128244: *3 http header: "Auth-SMTP-To: rcpt TO:<test@example.com>"
2020/02/14 11:24:04 [debug] 121280#128244: *3 http header done
2020/02/14 11:24:04 [debug] 121280#128244: *3 event timer del: 512: 1127939767
2020/02/14 11:24:04 [debug] 121280#128244: *3 generic phase: 0
2020/02/14 11:24:04 [debug] 121280#128244: *3 rewrite phase: 1
2020/02/14 11:24:04 [debug] 121280#128244: *3 search through nested static locations of ""
2020/02/14 11:24:04 [debug] 121280#128244: *3 test location: "/cgi-bin/nginxauth.cgi"
2020/02/14 11:24:04 [debug] 121280#128244: *3 using configuration "/cgi-bin/nginxauth.cgi"
2020/02/14 11:24:04 [debug] 121280#128244: *3 http cl:-1 max:1048576
2020/02/14 11:24:04 [debug] 121280#128244: *3 rewrite phase: 3
2020/02/14 11:24:04 [debug] 121280#128244: *3 http set discard body
2020/02/14 11:24:04 [debug] 121280#128244: *3 HTTP/1.1 204 No Content
Server: nginx/1.17.4
Date: Fri, 14 Feb 2020 10:24:04 GMT
Connection: close
Auth-Status: OK
Auth-Server: 192.0.2.222
Auth-Port: 25

2020/02/14 11:24:04 [debug] 121280#128244: *3 write new buf t:1 f:0 008AD6A0, pos 008AD6A0, size: 164 file: 0, size: 0
2020/02/14 11:24:04 [debug] 121280#128244: *3 http write filter: l:1 f:0 s:164
2020/02/14 11:24:04 [debug] 121280#128244: *3 http write filter limit 0
2020/02/14 11:24:04 [debug] 121280#128244: *3 WSASend: fd:512, s:164
2020/02/14 11:24:04 [debug] 121280#128244: *3 http write filter 00000000
2020/02/14 11:24:04 [debug] 121280#128244: *3 http finalize request: 0, "/cgi-bin/nginxauth.cgi?" a:1, c:1
2020/02/14 11:24:04 [debug] 121280#128244: *3 http request count:1 blk:0
2020/02/14 11:24:04 [debug] 121280#128244: *3 http close request
2020/02/14 11:24:04 [debug] 121280#128244: *3 http log handler
2020/02/14 11:24:04 [debug] 121280#128244: *3 free: 008ACC50, unused: 1161
2020/02/14 11:24:04 [debug] 121280#128244: *3 close http connection: 512
2020/02/14 11:24:04 [debug] 121280#128244: *3 reusable connection: 0
2020/02/14 11:24:04 [debug] 121280#128244: *3 free: 008AC848
2020/02/14 11:24:04 [debug] 121280#128244: *3 free: 0039FDE0, unused: 28
2020/02/14 11:24:04 [debug] 121280#128244: worker cycle
2020/02/14 11:24:04 [debug] 121280#128244: *1 mail auth http read handler
2020/02/14 11:24:04 [debug] 121280#128244: *1 WSARecv: fd:496 rc:0 164 of 1024
2020/02/14 11:24:04 [debug] 121280#128244: *1 mail auth http process status line
2020/02/14 11:24:04 [debug] 121280#128244: *1 mail auth http process headers
2020/02/14 11:24:04 [debug] 121280#128244: *1 mail auth http header: "Server: nginx/1.17.4"
2020/02/14 11:24:04 [debug] 121280#128244: *1 mail auth http header: "Date: Fri, 14 Feb 2020 10:24:04 GMT"
2020/02/14 11:24:04 [debug] 121280#128244: *1 mail auth http header: "Connection: close"
2020/02/14 11:24:04 [debug] 121280#128244: *1 mail auth http header: "Auth-Status: OK"
2020/02/14 11:24:04 [debug] 121280#128244: *1 mail auth http header: "Auth-Server: 192.0.2.222"
2020/02/14 11:24:04 [debug] 121280#128244: *1 mail auth http header: "Auth-Port: 25"
2020/02/14 11:24:04 [debug] 121280#128244: *1 mail auth http header done
2020/02/14 11:24:04 [debug] 121280#128244: *1 event timer del: 496: 1127939764
2020/02/14 11:24:04 [debug] 121280#128244: *1 reusable connection: 0
2020/02/14 11:24:04 [debug] 121280#128244: *1 free: 008AC040, unused: 196
2020/02/14 11:24:04 [debug] 121280#128244: *1 stream socket 496
2020/02/14 11:24:04 [debug] 121280#128244: *1 connect to 192.0.2.222:25, fd:496 #4
2020/02/14 11:24:04 [debug] 121280#128244: *1 event timer add: 496: 60000:1127939769
2020/02/14 11:24:04 [debug] 121280#128244: *1 malloc: 008AC040:4096
2020/02/14 11:24:04 [debug] 121280#128244: worker cycle
2020/02/14 11:24:04 [debug] 121280#128244: *1 post event 00897120
2020/02/14 11:24:04 [debug] 121280#128244: posted event 00897120
2020/02/14 11:24:04 [debug] 121280#128244: *1 delete posted event 00897120
2020/02/14 11:24:04 [debug] 121280#128244: *1 mail proxy dummy handler
2020/02/14 11:24:04 [debug] 121280#128244: worker cycle
2020/02/14 11:24:04 [debug] 121280#128244: *1 mail proxy smtp auth handler
2020/02/14 11:24:04 [debug] 121280#128244: *1 WSARecv: fd:496 rc:0 22 of 4096
2020/02/14 11:24:04 [debug] 121280#128244: *1 mail proxy send ehlo
2020/02/14 11:24:04 [debug] 121280#128244: *1 malloc: 0039FDE0:256
2020/02/14 11:24:04 [debug] 121280#128244: *1 WSASend: fd:496, 0, 25 of 25
2020/02/14 11:24:04 [debug] 121280#128244: worker cycle
2020/02/14 11:24:05 [debug] 121280#128244: *1 mail proxy smtp auth handler
2020/02/14 11:24:05 [debug] 121280#128244: *1 WSARecv: fd:496 rc:0 196 of 4096
2020/02/14 11:24:05 [debug] 121280#128244: *1 mail proxy send mail from
2020/02/14 11:24:05 [debug] 121280#128244: *1 WSASend: fd:496, 0, 47 of 47
2020/02/14 11:24:05 [debug] 121280#128244: worker cycle
2020/02/14 11:24:05 [debug] 121280#128244: *1 mail proxy smtp auth handler
2020/02/14 11:24:05 [debug] 121280#128244: *1 WSARecv: fd:496 rc:0 60 of 4096
2020/02/14 11:24:05 [debug] 121280#128244: *1 mail proxy send rcpt to
2020/02/14 11:24:05 [debug] 121280#128244: *1 WSASend: fd:496, 0, 45 of 45
2020/02/14 11:24:05 [debug] 121280#128244: worker cycle
2020/02/14 11:24:05 [debug] 121280#128244: *1 mail proxy smtp auth handler
2020/02/14 11:24:05 [debug] 121280#128244: *1 WSARecv: fd:496 rc:0 63 of 4096
2020/02/14 11:24:05 [debug] 121280#128244: *1 event timer add: 492: 86400000:1214280441
2020/02/14 11:24:05 [debug] 121280#128244: *1 event timer del: 496: 1127939769
2020/02/14 11:24:05 [info] 121280#128244: *1 client logged in, client: 127.0.0.1, server: 0.0.0.0:8025
2020/02/14 11:24:05 [debug] 121280#128244: *1 mail proxy handler: 1, #496 > #492
2020/02/14 11:24:05 [debug] 121280#128244: *1 WSASend: fd:492, 0, 63 of 63
2020/02/14 11:24:05 [debug] 121280#128244: *1 event timer: 492, old: 1214280441, new: 1214280441
2020/02/14 11:24:05 [debug] 121280#128244: worker cycle
2020/02/14 11:24:05 [debug] 121280#128244: *1 post event 008830C8
2020/02/14 11:24:05 [debug] 121280#128244: posted event 008830C8
2020/02/14 11:24:05 [debug] 121280#128244: *1 delete posted event 008830C8
2020/02/14 11:24:05 [debug] 121280#128244: *1 mail proxy handler: 0, #492 > #496
2020/02/14 11:24:05 [debug] 121280#128244: *1 WSARecv: fd:492 rc:0 6 of 4096
2020/02/14 11:24:05 [debug] 121280#128244: *1 WSASend: fd:496, 0, 6 of 6
2020/02/14 11:24:05 [debug] 121280#128244: *1 event timer: 492, old: 1214280441, new: 1214280441
2020/02/14 11:24:05 [debug] 121280#128244: worker cycle
2020/02/14 11:24:05 [debug] 121280#128244: *1 mail proxy handler: 0, #496 > #492
2020/02/14 11:24:05 [debug] 121280#128244: *1 WSARecv: fd:496 rc:0 50 of 4096
2020/02/14 11:24:05 [debug] 121280#128244: *1 WSASend: fd:492, 0, 50 of 50
2020/02/14 11:24:05 [debug] 121280#128244: worker cycle
2020/02/14 11:24:05 [debug] 121280#128244: *1 post event 008830C8
2020/02/14 11:24:05 [debug] 121280#128244: posted event 008830C8
2020/02/14 11:24:05 [debug] 121280#128244: *1 delete posted event 008830C8
2020/02/14 11:24:05 [debug] 121280#128244: *1 mail proxy handler: 0, #492 > #496
2020/02/14 11:24:05 [debug] 121280#128244: *1 WSARecv: fd:492 rc:0 170 of 4096
2020/02/14 11:24:05 [debug] 121280#128244: *1 WSASend: fd:496, 0, 170 of 170
2020/02/14 11:24:05 [debug] 121280#128244: *1 event timer: 492, old: 1214280441, new: 1214280535
2020/02/14 11:24:05 [debug] 121280#128244: worker cycle
2020/02/14 11:24:05 [debug] 121280#128244: *1 mail proxy handler: 0, #496 > #492
2020/02/14 11:24:05 [debug] 121280#128244: *1 WSARecv: fd:496 rc:0 56 of 4096
2020/02/14 11:24:05 [debug] 121280#128244: *1 WSASend: fd:492, 0, 56 of 56
2020/02/14 11:24:05 [debug] 121280#128244: worker cycle
....

<<<<<<<<<

Regards,
Sergey

13.02.2020 22:45, Yury Shpakov wrote:

Hi Sergey,


I reconfigured the config file as follows:

=== === ===
#user nobody;
worker_processes 1;

#error_log logs/error.log;
#error_log logs/error.log notice;
#error_log logs/error.log info;

#pid logs/nginx.pid;


events {
worker_connections 1024;
}


mail {
server_name localhost;
auth_http localhost:9000/cgi-bin/nginxauth.cgi;
# auth_http none;

smtp_auth none;
# smtp_auth login plain cram-md5;
# smtp_capabilities "SIZE 10485760" ENHANCEDSTATUSCODES 8BITMIME DSN;
xclient off;

server {
listen 8025;
protocol smtp;
proxy on;
proxy_pass_error_message on;
}
}

http {
server {
listen 9000;

location /cgi-bin/nginxauth.cgi {
add_header Auth-Status OK;
add_header Auth-Server 127.0.0.2; # backend ip
add_header Auth-Port 143; # backend port
return 204;
}
}
}
=== === ===

And now it's responding on port 9000 as expected:

=== === ===
C:\WINDOWS\system32>curl -H "Auth-Method: plain" -H "Auth-User: user" -H "Auth-Pass: pwd" -H "Auth-Protocol: imap" -H "Auth-Login-Attempt: 1" -i http://127.0.0.1:9000/cgi-bin/nginxauth.cgi
HTTP/1.1 204 No Content
Server: nginx/1.17.9
Date: Thu, 13 Feb 2020 21:30:54 GMT
Connection: keep-alive
Auth-Status: OK
Auth-Server: 127.0.0.2
Auth-Port: 143
=== === ===

However I'm still experiencing the same issue (in log file):

=== === ===
2020/02/13 16:29:24 [notice] 35048#26192: signal process started
2020/02/13 16:29:34 [error] 31732#22720: *1 WSASend() failed (10057: A request to send or receive data was disallowed because the socket is not connected and (when sending on a datagram socket using a sendto call) no address was supplied) while in http auth state, client: 127.0.0.1, server: 0.0.0.0:8025
=== === ===

Tried under both admin and regular user.

Any further ideas how to get it fixed please?


Thank you,
Yury

________________________________
From: Sergey Brester <serg.brester@sebres.de>
Sent: Wednesday, February 12, 2020 1:51 PM
To: Yury Shpakov <yshpakov@hotmail.com>
Cc: nginx-devel@nginx.org <nginx-devel@nginx.org>
Subject: Re: nginx for Windows - WSASend() socket error 10057


I answered inline...

12.02.2020 18:59, Yury Shpakov wrote:

Hi Sergey,


Thank you for you response.

I tried netstat /nabo and I don't see any reference to port 9000 at all.
So a problem is to make nginx to listen on port 9000 (as server)?
Or nginx is not listening on port 9000 but rather sending requests to port 9000 (as client)?
With setting of `auth_http`, you are defining an URL to the service responsible for authentication (and upstream choice).
Of course then you should have something that would response to the auth-requests (your own upstream, or some nginx location, or some "foreign" http-server).

See https://docs.nginx.com/nginx/admin-guide/mail-proxy/mail-proxy/ for more examples.
Maybe it's easier not to use auth_http at all? I was trying to remove it from configuration file but nginx was not happy.

I have my own auth-module so I don't know how it can be solved in stock-nginx without this directive.

Take a look here - https://serverfault.com/questions/594962/nginx-understanding-the-purpose-of-auth-http-imap-proxy - you can use some nginx location (and internal URL to same nginx instance) to specify that.

Anyway it is recommended to use some auth (on nginx side), because it'd preserve the resources of mail-servers, allow you to authenticate email clients with same user/password for all mail-servers (smtp, imap, pop3, etc) as well as the same user/pwd as for some other http-services. And it is used to choose an upstream server (if multiple) for the email processing.

At this point I don't need any authentication. I was told by my boss to use nginx for load testing of our service sending emails (SMTP client). I've got some SMTP Server and nginx would be used as SMTP proxy because it allows to set up delays.
Well, an auth request to some nginx-location would allow you to set up delays even on authentication phase.
And take into account that I REMOVED "--with-http_ssl_module" from parameters when I was building nginx.

And you advised to download some nginx.exe files but I believe they were built without "--with-mail" parameter (which I need).
Although, it was compiled with "--with-mail" (you can see all parameters in provided GH-linkhttps://github.com/sebres/nginx/releases/tag/release-1.13..0)
But it would not help, because basically your issue seems to be the configuration (not the nginx.exe).

Thank you,
Yury

________________________________
From: Sergey Brester <serg.brester@sebres.de>
Sent: Wednesday, February 12, 2020 7:38 AM
To: nginx-devel@nginx.org <nginx-devel@nginx.org>
Cc: Yury Shpakov <yshpakov@hotmail.com>
Subject: Re: nginx for Windows - WSASend() socket error 10057

It looks like your service defined in auth_http doesn't answer (or no listener on 127.0.0.1 port 9000?)...

try netstat (in cmd as admin):

netstat /nabo
netstat /nabo | grep -A 1 ":9000\b"

and check whether the listener on port 9000 is bound to 127.0.0.1 (or it is 0.0.0.0 only?) and it is the process you expect to see there (can be "reserved" by some other windows-service).

additionally try to telnet or curl it:

curl -H "Auth-Method: plain" -H "Auth-User: user" -H "Auth-Pass: pwd" -H "Auth-Protocol: imap" -H "Auth-Login-Attempt: 1" -i http://127.0.0.1:9000/cgi-bin/nginxauth.cgi

if it does not answer, make another attempt by replace 127.0.0.1 with 0.0.0..0 (or a host-name).

If it answers - see whether it is the expected response (some examples of good and bad responses are described in http://nginx.org/en/docs/mail/ngx_mail_auth_http_module.html).

But I guess if WSASend fails, it would probably (unexpected) reject the connection during the send (or even connect) process.
It can be also invalid (unexpected) content-length in keep-alive connect to auth-upstream - so send but still receive is expected (or vice versa).

Also follow this forum topic addressing similar issue: https://forum.nginx.org/read.php?2,257206,257207#msg-257207

Anyway it doesn't look to me like an issue of nginx (regardless windows or not), but you can also try some other ready build (for example on my GHhttps://github.com/sebres/nginx/releases/tag/release-1.13.0 - nginx.ziphttps://github.com/sebres/nginx/files/2246440/nginx.zip, where it works well).

Regards,
Sergey

12.02.2020 03:01, Yury Shpakov wrote:

Hi there,
Trying to make nginx work as SMTP server and/or SMTP proxy. Done everything according to:
http://nginx.org/en/docs/howto_build_on_win32.html
But excluded (don't care about SSL at this point so don't want to install/configure Perl now):
--with-openssl=objs/lib/openssl-master \
--with-openssl-opt=no-asm \
--with-http_ssl_module \
And added:
--with-mail
nmake was successful and nginx.exe was created.
However nginx.exe keeps failing with the error:
WSASend() failed (10057: A request to send or receive data was disallowed because the socket is not connected and (when sending on a datagram socket using a sendto call) no address was supplied) while in http auth state, client: 127.0.0.1, server: 0.0.0.0:8025
Windows API says the following about this error:

WSAENOTCONN
10057

Socket is not connected.
A request to send or receive data was disallowed because the socket is not connected and (when sending on a datagram socket using sendtohttps://docs.microsoft.com/en-us/windows/desktop/api/winsock/nf-winsock-sendto) no address was supplied. Any other type of operation might also return this error—for example, setsockopthttps://docs.microsoft.com/en-us/windows/desktop/api/winsock/nf-winsock-setsockopt setting SO_KEEPALIVEhttps://docs.microsoft.com/en-us/windows/desktop/winsock/so-keepalive if the connection has been reset.
https://docs.microsoft.com/en-us/windows/win32/winsock/windows-sockets-error-codes-2
Windows Sockets Error Codes (Winsock2.h) - Win32 apps | Microsoft Docshttps://docs.microsoft.com/en-us/windows/win32/winsock/windows-sockets-error-codes-2
Return code/value Description; WSA_INVALID_HANDLE 6: Specified event object handle is invalid. An application attempts to use an event object, but the specified handle is not valid.
docs.microsoft.com
Managed to debug your code in VS 2010 a little bit but it's brutal C so it's hard to figure your code out. And this debugger doesn't show you any local variables values.
Any recommendation for me to make it work?
Tried to play with config (commenting/uncommenting):
#user nobody;
worker_processes 1;
#error_log logs/error.log;
#error_log logs/error.log notice;
#error_log logs/error.log info;
#pid logs/nginx.pid;
events {
worker_connections 1024;
}
mail {
server_name localhost;
auth_http localhost:9000/cgi-bin/nginxauth.cgi;
# auth_http none;
smtp_auth none;
# smtp_auth login plain cram-md5;
# smtp_capabilities "SIZE 10485760" ENHANCEDSTATUSCODES 8BITMIME DSN;
xclient off;
server {
listen 8025;
protocol smtp;
proxy on;
proxy_pass_error_message on;
}
}
Tried both under a regular user and under admin. Tried on 25, 1025 and 8025 ports.
Thank you,
Yury


_______________________________________________
nginx-devel mailing list
nginx-devel@nginx.org<mailto:nginx-devel@nginx.org>http://mailman.nginx.org/mailman/listinfo/nginx-devel
_______________________________________________
nginx-devel mailing list
nginx-devel@nginx.org
http://mailman.nginx.org/mailman/listinfo/nginx-devel
Subject Author Views Posted

nginx for Windows - WSASend() socket error 10057

Yury Shpakov 227 February 11, 2020 09:04PM

Re: nginx for Windows - WSASend() socket error 10057

Sergey Brester 37 February 12, 2020 07:40AM

Re: nginx for Windows - WSASend() socket error 10057

Yury Shpakov 38 February 12, 2020 01:00PM

Re: nginx for Windows - WSASend() socket error 10057

Sergey Brester 37 February 12, 2020 01:52PM

Re: nginx for Windows - WSASend() socket error 10057

Yury Shpakov 43 February 13, 2020 04:46PM

Re: nginx for Windows - WSASend() socket error 10057

Yury Shpakov 37 February 13, 2020 04:50PM

Re: nginx for Windows - WSASend() socket error 10057

Sergey Brester 35 February 14, 2020 06:00AM

Re: nginx for Windows - WSASend() socket error 10057

Yury Shpakov 45 February 14, 2020 06:10PM

Re: nginx for Windows - WSASend() socket error 10057

Yury Shpakov 30 February 25, 2020 08:00PM

Re: nginx for Windows - WSASend() socket error 10057

Sergey Brester 29 February 26, 2020 04:52AM

Re: nginx for Windows - WSASend() socket error 10057 Attachments

Yury Shpakov 29 February 26, 2020 03:38PM

Re: nginx for Windows - WSASend() socket error 10057 Attachments

Sergey Brester 35 February 27, 2020 05:22AM

Re: nginx for Windows - WSASend() socket error 10057

Maxim Dounin 30 February 27, 2020 06:48AM

Re: nginx for Windows - WSASend() socket error 10057

Dipl. Ing. Sergey Brester 30 February 27, 2020 08:30AM

Re: nginx for Windows - WSASend() socket error 10057 Attachments

Yury Shpakov 29 February 27, 2020 02:42PM

Re: nginx for Windows - WSASend() socket error 10057

Maxim Dounin 58 February 28, 2020 08:28AM



Sorry, you do not have permission to post/reply in this forum.

Online Users

Guests: 67
Record Number of Users: 6 on February 13, 2018
Record Number of Guests: 421 on December 02, 2018
Powered by nginx      Powered by FreeBSD      PHP Powered      Powered by MariaDB      ipv6 ready